Workshop guide Fiat X1/9

Workshop · Fiat X1/9 1972–1989

Workshop guide Fiat X1/9

Maintaining the X1/9: the timing belt, the long cooling system, carburettor or injection, brakes and the targa roof.

Nederlandse versie

The engine bay of a Fiat X1/9
The engine bay of a Fiat X1/9. Photo: Wikimedia Commons, free licence; author and licence are on that page.

Which X1/9 do you have?

1300 (1972–1978)1290 cc, Weber 32 DMTR carburettor, four-speed box
1500 (from 1978/1979)1498 cc, Weber 34 DATR carburettor, five-speed box, electronic ignition
1500 with injectionAmerican cars from 1980/1981: Bosch L-Jetronic
Fiat or Bertoneuntil 1982 Fiat X1/9, then Bertone X1/9; engineering largely the same

For the X1/9 we deliberately give no settings, torque values or valve clearances as figures here. Use the workshop manual for your version (1300, 1500 with carburettor or with injection). A wrong value costs you an engine.

Maintenance schedule in brief

Every driveoil level, coolant, tyre pressures, lights
Every springchange oil and oil filter, check spark plugs, brakes, cables and rubbers
Per the handbookvalve clearance, carburettor or injection, ignition, gearbox oil
Timing beltevery three years or about 40,000 km, or sooner if the handbook says so
Every two yearsreplace brake fluid

The timing belt

Both engines have an overhead camshaft driven by a toothed belt. That belt is the X1/9’s most important maintenance item. If it breaks, you stop on the spot.

  1. Ask for proofIf you buy an X1/9, ask when the belt was last replaced. No proof? Then plan to replace it.
  2. Belt and tensioner togetherReplace the tensioner pulley at the same time. An old tensioner can still make a new belt jump teeth.
  3. Timing marksSet the engine to the marks from the workshop manual before you take the old belt off.
  4. TensioningTension the new belt as the handbook prescribes. Too tight or too slack shortens its life.
  5. Turn over and checkTurn the engine over twice by hand and check that all the marks line up again. Only then start it.

The cooling system

The radiator is at the front, the engine at the back. Between them long coolant pipes run through the body. That makes the cooling system sensitive: air in the system and rust in the pipes are the known problems.

Watch out for this

  • Always use the right coolant. Plain water makes the pipes rust from inside.
  • After a drive, look under the car to see whether coolant is dripping anywhere.
  • Keep an eye on the temperature gauge. If it rises, stop straight away.
  • If you have worked on the cooling system, bleed it according to the workshop manual. Trapped air causes overheating.
  • Rusted-through pipes rot the car from inside. Replace them in time.

Valve clearance

Measure the valve clearance with a cold engine and a feeler gauge. How to adjust it and which values apply to your engine is in the workshop manual. Work calmly and always measure again after adjusting.

Carburettor or injection

Tips

  • The 1300 has a Weber 32 DMTR, the 1500 a Weber 34 DATR. If it runs badly, have the carburettor rebuilt rather than adjusting it endlessly.
  • Replace a dirty air filter and old fuel hoses; hoses harden and can start to leak.
  • On the American injection cars: have faults traced by someone who knows Bosch L-Jetronic before you replace parts.

Brakes and suspension

Watch out for this

  • The X1/9 has disc brakes all round. The handbrake works via a cable on the rear calipers; check that they are not seizing.
  • The master cylinder often leaks and is awkward to reach. Check it regularly.
  • Replace the brake fluid every two years.
  • There is MacPherson suspension front and rear. At the rear the arms are adjustable; have the car aligned after work on the suspension.
  • You need special tools for the rear wheel bearings.

Body and targa roof

Watch out for this

  • Keep the drains by the roof free of dirt, otherwise water runs into the body.
  • The roof panel must fit snugly. If it leaks, the seals need replacing.
  • Regularly check the inner wheel arches, sills, floor and headlamp pods.
  • Rust in the bulkheads around the engine is hard to see. Repairing it sometimes means the engine has to come out.

SourcesWikipedia: Fiat X1/9 (English)Hagerty: Buying guide Fiat X1/9 (English)Registro X1-9: overview of the models (Italian)

← Back to the homepage